CuZn39Pb3 / Ms58 / 2.0401
CuZn39Pb3 is alloy of copper and zinc with lead additives . This alloy has similar properties to leaded bronzes . An important advantage of brass alloy is good workability.There can be manufactured a lot of things out of CuZn39Pb3 : complex-shaped devices , watch gears , bearings , branch conduits , pipes for chemical or […]
CW004A / C101
Electrolytic Tough Pitch Copper (ETP) C101 / CW004A is a commercially pure high conductivity grade of copper refined by electrolytic deposition which is then melted and oxidised to the “tough pitch” condition with a controlled low oxygen content. This is the most widely used of all the coppers because of its combination of electrical and […]
1.0711 / 10S10
One of the most widely used precipitation hardening grades in the business. While soft and ductile in the solution annealed condition, it is capable of high properties with a single precipitation or aging treatment. Characterized by good corrosion resistance, high harness, toughness and strength.Long, gummy chips characterize this alloys machinability. It can be machined in […]
EN AW 5754 / AlMg3
Aluminum 5754 is an aluminum alloy with magnesium as the primary alloying element, supplemented with small chromium and/or manganese additions. It has good formability when in the fully soft, annealed temper and can be work-hardened to fairy high strength levels. It is slightly stronger, but less ductile, than 5052 alloy. It is used in a […]
C40 / 1.0511
As a high-quality carbon structural steel, C40 is defined as a non-alloy steel with an average carbon content of about 0.4% as per European standards.C40 steel has high strength and good machinability, medium cold deformation plasticity, but poor in weldability and hardenability.C40 steel is used in normalized or quenched and tempered condition.It is often used […]
1.2210 / 115CrV3
1.2210 is a chromium vanadium alloy cold working steel commonly used in building parts. The cutting machinability of 1.2210 is good. This steel has excellent toughness and wear resistance. 1.2210 The material is difficult to weld and has average corrosion resistance. Polishing materials are not common, and material 1.2210 can harden well. 1.2210, also known […]
1.4104 / X14CrMoS17 / AISI 430F
1.4104 is a rust- and acid-resistant martensitic chromium steel with added sulfur, which improves its machinability. However, despite the high chromium content, the corrosion resistance is reduced due to the sulfur. Application areas The main application of this material are in areas that cause pitting or crevice corrosion. In addition, due to its excellent machinability, […]
1.2312 / 40CrMnMoS8-6 / P20+S / 40CMD8S
As one of the representative steel types of plastic mold steel, 1.2312 steel is developed on the basis of 1.2311 steel. 1.2312 steel uses Cr-Mn-Mo as a strengthening alloy element, and adds a higher content of sulfur element (0.05-0.1% ),which offers better machineability,30% increase in milling speed and 300% increase in drilling speed can be […]
PMMA / Acrylic
Poly (methyl methacrylate) is the scientific name for the synthetic polymer commonly known as acrylic, acrylic glass, and plexiglass. When not modified it is brittle, transparent, and lightweight.PMMA has a melting point of 320°F and has a density range of 1.17-1.20 g/cm3. It experiences no reactions by aqueous solution when compared to other polymers and […]
PE 500 / PE-HMW
PE 500 HMWPE is high molecular weight polyethylene with an average molecular mass of approx. 500 g/mol and a maximum density of 0.96 g/cm³. Its excellent mechanical properties, such as scratch and cutting resistance and resistance to acids and alkalis, together with its good sliding properties, make it a material that is ideal for machining. […]
